CLOCKS

Clock Dial

Problems With Clock Radios?



Sometimes alarm clock radios break down. However, we can take the time to repair them ourselves. The following is what to do to repair them.

 1. Check the power at the outlet, and make sure the power is on.

2. Check the pointer. Some household radios use a station frequency pointer mounted on a dial cord that is moved by a small wheel on the side of the clock radio. Other household radios use a digital frequency readout that cannot be adjusted.

3. If the sound is fuzzy, disassemble the unit and locate the volume control. Spray electrical contact cleaner into the control and rotate or slide the control several times to lubricate the mechanism.

4. Replace a damaged or broken antenna.

Most modern clock radios are built on printed circuit boards that can only be repaired by trained technicians. Some of the tools you may need are screwdrivers, wrenches, electronic control cleaner, denatural alcohol, soldering iron and solder.

Reset Dial Pointer

1. Turn on radio. Find a strong radio signal, listen to the frequency.

 

2. Use a piece of tape or grease pencil to mark the dial where the pointer should be for that frequency.

 

3. Unplug the receiver and open the housing. There are usually two to four screws in the underside of the radio.

 

4. Inspect the pointer mechanism for problems, such as a cord that came off at the end rollers, or a break in the cord. Replace the broken cord or repair it.

 

5. Loosen the spring clips Move the pointer along the dial cord until the station being received lines up with the tape or mark on the dial.

 

6.Tighten the clips on the cord. Make sure you do not move the pointer.

 

7. Plug the radio in and verify that the dial pointer reads correctly.

Replacing External Antenna

1. Loosen the antenna screw.

 

2. If there is no exterior screw, open the radio and access the antenna base.

Replacing an Internal Antenna

1. Unplug the receiver and open the housing.

 

2. Find and remove the internal antenna, of the internal base of the external antenna.

 

3. Inspect the wires wound around the antenna for serious damage. Make sure the antenna is firmly plugged into the main circuit board. If the antenna is damaged, replace it or attempt to repair the antenna, or replace the radio as a unit.

Clean Electronic Components

1. Unplug the receiver and open the housing.

 

2. Use canned air to blow dust from components, including any power cords and speaker jacks.

 

3. Use electrical contact cleaner, or a cotton swab dipped in dentured alcohol to clean electronic components.

 

4. If you find broken components on a circuit board, replace the circuit board. Before purchasing a circuit board, you can use a soldering iron and electronic solder to attempt a repair.

 

Now you have repaired the clock radio yourself.

 

Sometimes alarm clock radios break down. However, we can take the time to repair them ourselves. The following is what to do to repair them.

 

1. Check the power at the outlet, and make sure the power is on.

 

2. Check the pointer. Some household radios use a station frequency pointer mounted on a dial cord that is moved by a small wheel on the side of the clock radio. Other household radios use a digital frequency readout that cannot be adjusted.

 

3. If the sound is fuzzy, disassemble the unit and locate the volume control. Spray electrical contact cleaner into the control and rotate or slide the control several times to lubricate the mechanism.

 

4. Replace a damaged or broken antenna.

 

Most modern clock radios are built on printed circuit boards that can only be repaired by trained technicians. Some of the tools you may need are screwdrivers, wrenches, electronic control cleaner, denatural alcohol, soldering iron and solder.

Reset Dial Pointer

1. Turn on radio. Find a strong radio signal, listen to the frequency.

 

2. Use a piece of tape or grease pencil to mark the dial where the pointer should be for that frequency.

 

3. Unplug the receiver and open the housing. There are usually two to four screws in the underside of the radio.

 

4. Inspect the pointer mechanism for problems, such as a cord that came off at the end rollers, or a break in the cord. Replace the broken cord or repair it.

 

5. Loosen the spring clips Move the pointer along the dial cord until the station being received lines up with the tape or mark on the dial.

 

6.Tighten the clips on the cord. Make sure you do not move the pointer.

 

7. Plug the radio in and verify that the dial pointer reads correctly.

Replacing External Antenna

1. Loosen the antenna screw.

 

2. If there is no exterior screw, open the radio and access the antenna base.

Replacing an Internal Antenna

1. Unplug the receiver and open the housing.

 

2. Find and remove the internal antenna, of the internal base of the external antenna.

 

3. Inspect the wires wound around the antenna for serious damage. Make sure the antenna is firmly plugged into the main circuit board. If the antenna is damaged, replace it or attempt to repair the antenna, or replace the radio as a unit.

Clean Electronic Components

1. Unplug the receiver and open the housing.

 

2. Use canned air to blow dust from components, including any power cords and speaker jacks.

 

3. Use electrical contact cleaner, or a cotton swab dipped in dentured alcohol to clean electronic components.

 

4. If you find broken components on a circuit board, replace the circuit board. Before purchasing a circuit board, you can use a soldering iron and electronic solder to attempt a repair.

 

Now you have repaired the clock radio yourself.

 

Sometimes alarm clock radios break down. However, we can take the time to repair them ourselves. The following is what to do to repair them.

 

1. Check the power at the outlet, and make sure the power is on.

 

2. Check the pointer. Some household radios use a station frequency pointer mounted on a dial cord that is moved by a small wheel on the side of the clock radio. Other household radios use a digital frequency readout that cannot be adjusted.

 

3. If the sound is fuzzy, disassemble the unit and locate the volume control. Spray electrical contact cleaner into the control and rotate or slide the control several times to lubricate the mechanism.

 

4. Replace a damaged or broken antenna.

 

Most modern clock radios are built on printed circuit boards that can only be repaired by trained technicians. Some of the tools you may need are screwdrivers, wrenches, electronic control cleaner, denatural alcohol, soldering iron and solder.

Reset Dial Pointer

1. Turn on radio. Find a strong radio signal, listen to the frequency.

 

2. Use a piece of tape or grease pencil to mark the dial where the pointer should be for that frequency.

 

3. Unplug the receiver and open the housing. There are usually two to four screws in the underside of the radio.

 

4. Inspect the pointer mechanism for problems, such as a cord that came off at the end rollers, or a break in the cord. Replace the broken cord or repair it.

 

5. Loosen the spring clips Move the pointer along the dial cord until the station being received lines up with the tape or mark on the dial.

 

6.Tighten the clips on the cord. Make sure you do not move the pointer.

 

7. Plug the radio in and verify that the dial pointer reads correctly.

Replacing External Antenna

1. Loosen the antenna screw.

 

2. If there is no exterior screw, open the radio and access the antenna base.

Replacing an Internal Antenna

1. Unplug the receiver and open the housing.

 

2. Find and remove the internal antenna, of the internal base of the external antenna.

 

3. Inspect the wires wound around the antenna for serious damage. Make sure the antenna is firmly plugged into the main circuit board. If the antenna is damaged, replace it or attempt to repair the antenna, or replace the radio as a unit.

Clean Electronic Components

1. Unplug the receiver and open the housing.

 

2. Use canned air to blow dust from components, including any power cords and speaker jacks.

 

3. Use electrical contact cleaner, or a cotton swab dipped in dentured alcohol to clean electronic components.

 

4. If you find broken components on a circuit board, replace the circuit board. Before purchasing a circuit board, you can use a soldering iron and electronic solder to attempt a repair.

 

Now you have repaired the clock radio yourself.

 

TheWatchTheClock.Com

 

About the Author

The author is retired.  She keeps herself busy by doing things she likes to do.  Here are some of her hobbies:  gardening, reading, cooking, baking,hiking, and occasionally dabbles into writing. She also enjoys traveling.

UK people: The talking clock... (dial 123) WHY have they changed it to this mad woman!?

Instead of that posh woman, telling you the time... they've got some nutcase "tinkerbell" taking over instead... speaking in a ridicules american accent.

Whats that about!?

I've just checked that. What the hell?!
She sounds awful, I know they have a tinkerbell film coming out soon, if not now but that's no reason to put her there?

How To Remove An Antique Clock Dial

Tags: clock dial refinishing, clock dial restoration, clock dials, clock dials bezels, clock dials for sale

This entry was posted on Monday, January 25th, 2010 at 12:11 am and is filed under collectibles clocks. You can follow any responses to this entry through the RSS 2.0 feed. Both comments and pings are currently closed.